This collection highlights materials research and innovations for a wide breadth of energy systems and technologies. The volume includes papers organized into the following sections:Energy and Environmental Issues in Materials Manufacturing and ProcessingMaterials in Clean PowerMaterials for Coal-Based PowerMaterials for Energy Conversion with Emphasis on SOFCMaterials for Gas TurbinesMaterials for Nuclear EnergyMaterials for Oil and Gas
Inhaltsverzeichnis
Part 1: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in the Steel Industry. - Waste Energy Recovery Technology of Iron and Steel Industry in China. - Green Manufacturing Process of Shougang Jingtang Steel Plant. - The Introduction and Process Optimization Research of Oxygen Blast Furnace Ironmaking Technology. - Prediction and optimal scheduling of byproduct gases in steel mill: Trends and challenges. - Processing Non-Oriented Electrical Steels Using Inclined/Skew Rolling Schemes. - A Possible Way for Efficient Utilization of Coal Energy: The Combined Process of Ironmaking with Gasoline Synthesis and Electricity Generation. - The influence of water vapour on the fuming rate in a ferromanganese system. - Part 2: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in Aluminum Production, Waste Heat and Water Recovery. - Approach for pyrolysis gas release modelling and its potential for enhanced energy efficiency of aluminium remelting furnaces. - Numerical approach for the implementation of the interaction of pyrolysis gases and combustion products in an aluminium melting furnace. - Fluoropolymer Coated Condensing Heat Exchangers for Low-grade Waste Heat Recovery. - Nitrate and other anion removal from waste water using the Hydroflex technology. - Mechanical Analysis of Raceway Formation in Bulk Bed of Blast Furnace. - Part 3: Materials for Coal-Based Power: Materials For Coal-Based Power: Session I. - Ni-Fe based alloy GH984G used for 700 coal-fired power plant. - Part 4: Materials for Coal-Based Power: Materials For Coal-Based Power: Session II. - Creep strength and oxidation resistance of industrially made G115 Steel pipe. - Accelerated creep test for new steels and welds. - Part 5: Materials for Coal-Based Power: Materials For Coal-Based Power: Session IV. - The Reliability Analysis of 12Cr1MoVG and T23 Used for USC Boilers Water Wall. - Part 6: Materials for Coal-Based Power: Poster Session. - Effect ofhigh-frequency induction hardening on stress corrosion of a 12% Cr martensitic stainless steel. - Fireside corrosion behaviors of Inconel 740 H superalloy in various SO2 contents. - High Cycle Fatigue Behavior of HAYNES282 Superalloy. - Recent Development in the Characteristics of Alloy 625 for A-USC Steam Turbine Castings. - Part 7: Materials for Gas Turbines: Coatings. - EVOLUTION OF THE THERMAL CONDUCTIVITY OF Sm2Zr2O7 UNDER CMAS ATTACK. - Part 8: Materials for Gas Turbines: Hot Corrosion and New Materials. - Development of a new high strength and hot corrosion resistant directionally solidified superalloy DZ409. - Part 9: Materials for Gas Turbines: Microstructure and Processing. - Modeling the Diffusion of Minor Elements in Different MCrAlY Superalloy Substrates at High Temperature. - ON HEALING MECHANISM OF CAST POROSITIES IN CAST NI-BASED SUPERALLOY BY HOT ISOSTATIC PRESSING. - The Influence of Dendritic Segregation Degree to the Recrystallization Nucleation in U4720LI. - Part 10: Materials for Gas Turbines: Poster Session. - Stress Rupture Properties of Alloy 783. - Study on the Undercoolability and Single Crystal Castability of Nickel-Based Superalloys. - Part 11: Materials for Nuclear Energy: Materials for Nuclear Applications I. - Enhancing the High-Cycle Fatigue Property of 316 Austenitic Stainless Steels through Introduction of Mechanical Twins by Cold-Drawing. - Part 12: Materials for Nuclear Energy: Materials for Nuclear Applications II. - Microstructure Evolution of a Reactor Pressure Vessel Steel during High-temperature Tempering. - Part 13: Materials for Nuclear Energy: Environmental Effects. - Effect of Steam Pressure on the Oxidation Behaviour of Alloy 625. - Friction Stir Processing of Degraded Austenitic Stainless Steel Nuclear Fuel Dry Cask Storage System Canisters. - Part 14: Materials for Nuclear Energy: Accident Tolerant Fuels & Irradiation Effects. - The Mechanical Response of Advanced Claddings during Proposed Reactivity Initiated Accident Conditions. -First principles investigations of alternative nuclear fuels. - Comparative study of thermal conductivity of SiC and BeO from ab initio calculations. - Part 15: Materials for Oil and Gas and AMREE Oil & Gas III. - Anisotropic behaviors for X100 high grade pipeline steel under stress constraints. - Co-relation of microstructural features with tensile and toughness characteristics of X70 grade steel. - Development and applications of new generation Ni-containing cryogenic steels in China. - Microstructure analysis and weldability investigation of stainless steel clad plate. - Microstructure and Properties of High Performance Pipeline Steels. - Sensitivity variation of nanomaterials at different operating temperature conditions.